Overview
With a multi-port USB-RS232 splitter (hub), one Axion Displays Radar Node can monitor and control up to 8 projectors over RS232 instead of one. You plug the hub into the node’s USB port and connect one projector to each RS232 port.
In the Radar dashboard, each projector on a port becomes its own device. It has its own protocol, limits, alerts, history and commands. The node itself becomes a plain “Radar Node” that carries the projectors’ data to the cloud.
Use a hub when several projectors are installed close together, for example in one projection room or one rack. Hubs come in a 4-port and an 8-port version. Each node can have one hub.
What you need
| Item | Notes |
|---|---|
| Radar Node | Online and visible in the dashboard. |
| Multi-port USB-RS232 hub | 4-port or 8-port, ordered under → or at sign-up. |
| RS232 cable per projector | Straight or null-modem, depending on the projector. Use the same cable type that works with a single node. |
| Connected-devices plan | Needed only if your plan bills per display. Each node includes one display; every extra projector counts towards your plan. |
| Dashboard role | Super admin or integrator for the organization that owns the node. |
Every projector needs an RS232 protocol in Radar. Projectors of the same model can share one protocol. PJLink is optional and set per projector.
Installation
Setup takes about 10 minutes per node. The node detects the hub by itself; you then attach a projector to each port in the dashboard.
- Plug the hub into a USB port on the Radar Node. Keep it in the same USB port from now on.
- Connect each projector’s RS232 port to a port on the hub. Note which projector is on which port (port 1, 2, 3 …).
- Wait about a minute. The node reports the hub’s ports to the dashboard.
- In the dashboard, open and scroll to . Your node shows a card with one row per port.
- On each port with a projector, type a name (for example “Hall 2 left”) and click Add projector.
- Click Edit on the new projector. Check its protocol, product, location and, if used, its PJLink address and password.
- Within about a minute the projector starts reporting. It appears in under its node.
The first projector you add takes over the node’s protocol, product and model, so a node that already monitored one projector keeps its settings. After that, the node itself no longer reads a serial port.
Each projector gets a device ID made of the node ID and its port, for example 46a96b6-P3 for port 3.
In the Radar dashboard
Each projector behaves like a normal device; the node is shown as its parent.
| Where | What you see |
|---|---|
| Hardware Fleet | The node, labelled “Multi-port node · N projectors”, followed by its projectors (indented, with port and name). The node shows no product data of its own. |
| Topology | Projectors drawn under their node; their status counts towards the site. |
| Device page | A projector links to its node; the node lists its projectors. |
| Alerts | Rules and offline alerts work per projector. If the node goes offline, you get one alert for the node, not one per projector. Its projectors show NODE OFFLINE. |
| Commands and automations | Sent to that projector’s port only. |
| Reboot | On a projector, Restart projector restarts only that projector (its protocol’s reboot command, or a power off/on cycle). It never restarts the node. A scheduled “Reboot Node” only restarts nodes. |
| Version Compliance | Each projector reports its own firmware. |
| Ambient sensor | A USB temperature/humidity sensor stays on the node and is shown on the node. |
To rename a projector, change its name on the Multi-port card and click Save. To remove one, click the bin icon; this also deletes its history.
Troubleshooting
| Problem | Likely cause | What to do |
|---|---|---|
| No Multi-port card for the node | The node hasn’t reported the hub yet, or sees fewer than 2 ports. | Check the node is online. Re-seat the hub’s USB cable, wait 1-2 minutes, reload the page. |
| Port shows “Not detected – hub unplugged?” | The node no longer sees that port. | Check the hub’s USB cable and power. Use the same USB port on the node as before. |
| Projector added but shows no data | Wrong protocol, wrong cable type, or wrong port. | Check Edit → protocol. Try a null-modem adapter (or remove it). Confirm the projector is on the port number shown. |
| Data from the wrong projector | Cables swapped between ports. | Projectors follow the port number. Swap the cables back, or rename the projectors to match. |
| “At its connected-devices limit” when adding | Your plan’s display count is used up. | Raise under , then add the projector again. |
| All projectors show NODE OFFLINE | The node itself is offline. | Check the node’s power and network. The projectors return when the node does. |
| Yellow “This node still acts as a projector itself” box | The node was converted before the dashboard did this automatically. | Pick a projector and click Finish conversion. Its automations move there; “Reboot Node” stays on the node. Check its alert rules under . |
| Restart projector does nothing | The protocol has no reboot or power on/off buttons. | Add a Reboot button (generic action “Reboot”) or Power On/Off buttons to the protocol. |
FAQ
Can I mix projector models on one hub? Yes. Each projector has its own protocol; set it with Edit.
Can I swap the hub for a new one? Yes. Connect the projectors to the same port numbers on the new hub. Radar picks up the new hub within a minute.
Do projectors count towards my device limit? Not towards the node limit. If your plan bills per connected display, every projector after the first on a node counts.
Can I use more than one hub per node? No. One hub per node, with up to 8 ports.
Does PJLink still work? Yes, per projector. Enter its PJLink address and password under Edit.
When to contact support: a port stays “Not detected” after re-seating the hub, or a projector shows no data after you’ve checked the protocol and cable. Send the node ID, the port number and the projector model.
