Welcome to the Axion Displays Projector Calculator. This interactive 3D tool helps you plan, visualize and check projection installations, from a single projector to a multi-projector blend.
1. Choose Your Setup and Hardware
At the top of the left sidebar, set up the basics:
- Units: Switch between Metric (m) and Imperial (ft).
- Layout: Choose Single for one projector, Two for two projectors with their own settings, or Blend Grid for identical projectors blended in columns and rows.
- Orientation: Choose Landscape, or Portrait for projectors turned 90° (the image is taller than it is wide).
- Mounting: Choose Tabletop, or Ceiling (inverted) for projectors mounted upside down.
Then choose your equipment under Hardware:
- Projector Series: Choose a model from the Digital Projection range (E-Vision, M-Vision, Titan or Satellite).
- Lens Model: Choose the lens for your application. The calculator automatically applies that lens’s throw ratio range, lens shift limits and focus distances.
- Screen Size: Enter the image width or the diagonal (in inches) directly. Click Lock to keep the screen size fixed: distance and throw ratio then change together.
2. Configure the Installation
Under Installation, set where the projector sits in the room:
- Distance: The throw distance, from the lens to the screen.
- Mount Height: The height of the projector above the floor.
- Side Offset: Move the projector to the left or right.
3. Fine-Tune Optics and Shift
Under Optics & Shift, adjust the image position and size:
- V-Shift / H-Shift: Move the image vertically or horizontally with lens shift, as a percentage of the image height or width. The calculator keeps you within the mechanical limits of the selected lens.
- Throw Ratio: With a zoom lens, use this to change the image size without moving the projector.
- Shift image up above the floor: If the image reaches below the floor, this button shifts it up just enough.
The calculator shows a warning when:
- the distance is outside the lens’s focus range
- a locked screen size can’t be made in focus with this lens
- the image reaches below the floor
With two projectors, Match Projector 2 Settings copies the settings from one projector to the other.
4. Analyze the Results
The results panel updates as you change your setup:
- Dimensions: Image width, height, diagonal and screen area.
- Brightness: Estimated screen brightness at 1.0 gain, based on the projector’s lumens and the screen area. It’s shown in nits (cd/m²) in metric and in foot-lamberts (fL) in imperial.
- Resolution: Native resolution, pixel pitch and pixel density.
Two projectors or a Blend Grid: Set the blend overlap (horizontal and vertical for a grid, and columns and rows). Combined Coverage then shows the total width, height, diagonal, area, resolution and pixel pitch. Click Open in Blend Calculator to continue with the same setup there.
Room & Audience:
- Audience shadow check: Shows where people standing in front of the screen would cast a shadow on the image. This check works with Single and Two layouts, not with a Blend Grid.
- Ceiling mounting: The calculator shows where the ceiling is and warns when an image reaches above it. Click Shift images below the ceiling to fix it with lens shift.
5. Navigate the 3D View
Use the 3D view to look at your setup from any angle:
- Rotate: Click and drag with the left mouse button.
- Pan: Click and drag with the right mouse button.
- Zoom: Use the mouse scroll wheel.
- View buttons: Jump to the Top, Left, 3D, Right or Front view.
- Fit to Screen: Reset the camera to the default view.
You can also edit the setup directly in the 3D view:
- Move: Click a projector or its screen, then move it with the arrow keys (←/→, ↑/↓) or Page Up/Page Down.
- Select both: Shift+click to select both projectors. Moves and slider changes then apply to both.
- Remove: Press Delete to remove projector 2.
- Undo / Redo: Ctrl+Z undoes, Ctrl+Y redoes.
- Snapping: Hold Alt while dragging to turn snapping off.
6. Save and Share
- Copy Link: Copies a link with all your current settings to your clipboard, so you can share the exact setup with colleagues or come back to it later.
- Download PDF: Creates an Axion Displays specification report with your 3D view, technical drawings, all configuration details and a recommended media server.
- Request Quote: Sends your setup directly to the Axion Displays team for a quote or a technical review. You can choose to be contacted by WhatsApp.
